How to do what the performance deteriorated buried

ncycgdxhl

How to do what the performance deteriorated buried

Avoid damage to components. Work in the fields and the process should pay attention to the working parts to listen to if there was any noise in operation. Once discovered, should immediately stop checks, find out the reasons,[link widoczny dla zalogowanych], to be re-operations only after troubleshooting. Work, the universal joint should be close to the level of the position; promoted, universal joints and the horizontal angle should be less than 30. . If the rotation about the direction of plows (horizontal) is not level, adjust the triangular rod to reach the horizontal level. El rotary plows often transport, should be removed joints. In the headland turning and reversing, rotary plows must be raised in order to avoid the blade deformation or fracture. In the transfer of land, should rise to the highest position rotary plow, cut off the power while the power output shaft. If the transfer distance, locking device must be fixed. Each rotary plows working 3h ~ 4h, to check and clean the blade should be kept down cleaning up, should the engine stall; or encountered mechanical aging, poor performance of the tractor, there sets of automatic clutch slipped, so tractor automatically Guadang to accidents. If the machine does not turn off hand in case of tractor rotary plows clearing the debris, the best units in the first high-end low-stopping place,[link widoczny dla zalogowanych], and pre-sets of gear to control the clutch lever with a rope tie him to prevent the stampede . Clean up, to the security of a 2m long scythe handle, people standing far away from the rotary plows 1m to clean up the place, and remain vigilant. Crop residues and weeds to reduce the winding coulter shaft, but also in the far left and far right to install the two coulter, put two bolts about 10cm longer. Whether reasonable adjustments before using rotary tiller, rotary tiller is directly related to the life quality and rotary tiller. Therefore, rotary tiller should pay attention to the following adjustments. (1) about the level of adjustment will be fragmented Rotary ground, check the left and right ends are the same tip height from the ground, shot through the right crank to adjust to enhance and ensure tillage depth of about the same. (2) levels before and after adjusting down to first Rotary tillage depth required to change the adjusting rod (the central rod) in length, so that was the level of the middle gear case status: (3) Lifting height adjustment of the tilt gimbal angle is too large, easy to damage joints and power output shaft. Therefore, the required time of universal joint angle in the small rises over 30. . General tip about 20em can turn off the ground and air lines; for easy operation, fields and operations, the maximum increase should be limited to the location, that is the manual adjustment of the limit E sector plate screws in place,[link widoczny dla zalogowanych], so that each raising the height remains unchanged. (4) the performance of the adjustment pulverizer pulverizer performance and tractor forward speed and the speed of the knife shaft, in general, strong winter Luan mouth, it can be improved by changing the forward speed to the middle of pulverizer gearbox with the performance of the rotary machine is also Town by changing the knife shaft speed to improve pulverizer performance to adapt to different soil requirements: (5) the adjustment of equipment and tillage depth adjustment and bit stronger regulator for the hydraulic system of tractor rotary operation, manual adjustment should be used to prohibit the use of force regulation to avoid damage to the rotary tiller. Operation,[link widoczny dla zalogowanych], when the rotary tiller tillage depth to meet the requirements, you should use the limit screws to adjust the handle position to block, so that each time the same tillage depth. If the split with a hydraulic system of tractor rotary operation, the distributor should be placed on the floating position of the handle, rotary machine with the same set of deep tillage on the piston rod to adjust the positioning clamp; decrease or enhance the rotary tiller , should quickly pull the handle or upgrade to a floating position, not position in the fall or remain neutral to avoid damage to the rotary tiller:! chu chu chu chu chu nose! chu workers squirming cockroach creeping Fun:! j plowed suspension performance deterioration of the main reasons are: poor technical condition of the plow itself, such as the Plowshare blunt or sharp bend deformation Hua; hanging knot or improperly adjusted equipment, such as the suspension is unreasonable to determine position, low position of the upper and lower connecting rod; soil excellent compaction; plow the quality of the light. For different reasons,[link widoczny dla zalogowanych], may take the following methods to adjust. When buried, the body must be buried plow how to do worse performance why forward, Hua was the first tip, the angle should be buried 3. 5. Range; Hua edge should be greater than the pressure on soil strength of soil. Hanging on the technical state of good plow land when performance is poor if buried, generally adjusting the hanging position, so that the upper and lower suspension points plow mount holes. To increase the plow buried moment: If it is still hard buried, may be appropriate to adjust the lever a short, buried to increase the angle, while the right tone to enhance the short rod, the forward plow frame was left to reach the same before and after deep plowing; using the above method to adjust After the buried remains difficult, in the rear of the plow frame with appropriate weight (people should not sit on the plow) (Winter) * celebrity famous man empties his purse, no one can take it away. Investment knowledge, to benefit most. - Benjamin Franklin Rotary How transfer so that not to hurt the local security and cleaning rotary blade