Seabuckthorn fruit juice processing machinery and

e707004304

Seabuckthorn fruit juice processing machinery and ancillary equipment selection

With the problem. In the selection of the evaporator, it is usually based on the nature of the solution by evaporation, such as bonding, foaming, corrosion, heat-sensitive, scaling, crystallization and other aspects to consider, the selection of the evaporator should be able to ensure that production - Language quality, higher productivity and economic benefits. Seabuckthorn juice is a strong heat-sensitive materials, which use the evaporator should be focused on meeting the strong features of heat-sensitive as possible to lower the material in the evaporator boiling point, reduce the material in the evaporator of the retention time. There are a number of sea buckthorn plant, concentrated equipment selection SRP-K vacuum evaporation pan. Relatively cheap price of the equipment,[link widoczny dla zalogowanych], production capacity is relatively modest. However, the material in a longer residence time in the evaporator, Vc loss of more, up to about 5��. Therefore, the choice of the device is not fruit juice concentrate reasonable. Vacuum thin film evaporator, the material into the membrane at high speed through the heating wall. Heat transfer coefficient, the heating steam temperature and boiling temperature difference between the material and the material is no longer one-way flow through the loop, therefore, the material in the evaporator towel short residence time (only a few seconds.) So, for that fruit juice and heat-sensitive animals,[link widoczny dla zalogowanych], film evaporator is ideal. Lz a centrifugal thin film evaporator 2.6 successfully combines the vacuum thin film evaporator and the working principle of centrifugal separation of the two, in its internal, juice was 3.00 times the film strength of the centrifugal force Peng, the flow rate much higher juice film constantly updated, greatly enhancing the heat transfer effect, is a new type of evaporator Higher Education, is currently one of the most advanced equipment In addition, the low evaporation temperature machine (50 ~ 56 ��), the surface heating in the heating juice time is short (less than 1 second cast.) Thus, a 2.6 Lz centrifugal thin film evaporator is the best fruit juice concentrate equipment. The main parameters are as follows: heat transfer area {2.6m. Evaporation capacity: 9ookg / h (water) heat transfer coefficient: 3600 kcal / m �� (water) vapor pressure: 680mm Hg (vacuum), 0.5kg/cm. (Gauge) steam consumption: lO00 ~ llOOkg / h (maximum) cone diameter: 6650mm cone number: 6 Speed: 60011/min motor power: 4kw Weight: 1500kg (host)} 4200kg (Unit) Dimension 1000 �� I200 �a� 700 (ram) (host), 4300 �� 3000 �� 4500 (ram) (Units) 22 seabuckthorn However, Lz a centrifugal thin film evaporator 2.6 productivity of some larger. Pharmaceutical & Chemical Machinery Factory in Xiamen has been a successful trial Lz-O. 5 centrifugal film evaporator, the evaporation capacity of 200kg / h, this model is too small to moderate productivity,[link widoczny dla zalogowanych], should be selected. 2.8 Cooling equipment sterilization or concentrated fruit juice,[link widoczny dla zalogowanych], should be rapidly cooled to below 38 �� to reduce the dimension C losses. According to process requirements, cooling equipment should be closed, while the commonly used cooling medium is water,[link widoczny dla zalogowanych], so the choice of horizontal sandwich sRP-GT milk cans. The main parameters are as follows; effective volume: 2000l cooling jacket size: 1.4m diameter agitator lodicules: 500ram agitator speed: 36n / / lqin motor: XLD-O. 4-3 discharge port diameter: 50mm Weight: about 1000kg2.9 pump juice in the production process, up and down process of asking the connections needed by pipeline and pump connections. Optional sDP-E sanitary pumps. The main parameters are as follows: flow l3t / h Head: 5113. I1r film wins Path: 150ram export diameter: 32film Motor: J03-8Ol a 4T2, power 0.5kw Overall dimensions: 475x258 �� 330 (m113.) Weight t36kg2.10 tank processes to connect between the tank and need to have j ��Dong, productivity of equipment need more storage tanks do not deserve. Tank volume is generally 1 ~ 2m. , According to the procedure to determine the actual situation, make or buy. 3 Conclusion 3.1L maple above the selected machines and equipment, reasonable structure, advanced performance, easy operation, fully able to meet technical requirements, thus ensuring the smooth implementation process and the quality and quantity of production tasks to complete the selected mechanical and 32L above equipment, in addition to juice, the remaining capacity of the device is basically a 4 ~ 5t / classes, is assigned, Taiwan reasonable, juice production capacity of 1.5t / class or day can be used to open the second of two parallel , Three ways to solve thus ensuring coordination between these various processes and balanced production. 3.3 The selected major machinery and equipment, have made a process test (see related articles on technology test))