ugg boots billig Mine car wheels changer in Fangez

xp574088

Mine car wheels changer in Fangezhuang Mine

Working plate; ⑥ out Paxia wheel shell, on the appropriate location; ⑦ If it is closed wheel, the U-shaped card, removed from the right-axis drive, the card on the left, put the wedge inserted in the activities of care-axis frame the middle of the U-shaped slot, and then pull the handle mounted to the valve Pa extended position, at this time, working out of cylinder piston rod, sliding axle care will be mine shaft bracket clamped plate at the same time as the work right Move up to the left until the shell off; ⑧ wheel if it is open, you will need the free end of the first round of the Shang Hao channel nut shell,[link widoczny dla zalogowanych], and then picking the other side of the round shell. (2) Steak Grilled with wheel bearing shell operation method, the difference is: ① Grilled closed wheel bearings should be first nut down, then picking the side of the bearing sleeve bearing block after picking on the set screw nuts, Unscrew the nut and then the other side, before picking the side bearing nut-free; ② clawed type wheel bearings should be re-tightening the nut slot at one end, and then picking the other end bearings. Paxia bearing block fitted with sets of post, screw on the nut and then the other side of Pa; ③ the nut on the left side, the card U-shaped chuck, round shell method is by picking the handle; ④ When the side of the bearing after Paxia should be dedicated without condom bearing block bearing side, and tighten the nut, the left wheel stuck in the machine inside the nest, and then, and then picking the other side of the bearings. (3) adjustment of the pressure loaded bearing ① (recommendation 5 ~ 6MPa can); ② pull the operating handle to the extended position, so that the work of the first out, the bearing sleeve drive wheel mounted on the right side of the barn; ③ shaft flat prop shaft on the rack, pull the shaft gear shaft inserted in the header side positions revolver head so as not to block the traverse axis, and then sets of bearings on the bearing plate (bearing nest), to ensure the bearing and the axis perpendicular to the plane. Pull the valve handle to return, and make the work head slowly back and pressed bearing end. Along the shaft when the bearing pressure on people to a specific location, quickly pull the valve handle to the extended position; the plate and bearing from the bearing sleeve; ④ round of the valve operating handle mounted pull Pa to the extended position, so that the work head out,[link widoczny dla zalogowanych], fitted across the Central and the other plate bearing, you can repeat the operation. If it is open-wheel, the outer bearing (bearing the most recent off-axis head) should be installed in the round of the shell and then fitted; ⑤ pull handle mounted to the steak out, and make the cylinder heads out of work, adjusting shaft direction, mounted the other side of the bearing, the method above. (4) mounted wheel shell ① pull the expense of operating handle mounted to the extended position,[link widoczny dla zalogowanych], so that the work of the first out,[link widoczny dla zalogowanych], the shell mounted on the piston rod wheels work on disk (the right wheel position) in; ② will be installed bearing nuts and other parts flat on the prop shaft after shaft rack righting help stabilize; ③ the round shell holes (or nest) put shaft is aligned, adjusted and fine-tune the frame by hand to stabilize the round shell, and then mounted wheel valve operating expense pull the handle to the return position,[link widoczny dla zalogowanych], to allow work to live round the head shell, and slowly pressure on people to the specified location; ④ adjust the direction of the shaft, repeat the above operation, the final round with a grasping forceps to live the middle of the shaft, and remove the lift has been installed Good wheel off the power. 6 Notes (1) wiring, you must check the motor rotation to ensure that their turn to turn consistent with the calibration of the motor, not reverse, otherwise, it will damage the pump. (2) after the installation and use should be checked before the connection is solid parts, whether oil spills, leakage phenomenon, whether there are abnormal sounds and not working place. (3) Check the operating handle is flexible, it can be automatically stopped in the middle to start the pump, check and adjust the working pressure, picking shells and bearing wheels when pressure is generally adjusted in 1O12MPa, shell and wheel bearing assembly when the pressure is 56MPa, any under pressure shall not exceed 16MPa. (4) Steak equipment operation, operators are not allowed on any part of the body shaft and bearings (wheel shell) or between the bearings (wheel shell) between the head and work, supporting the shaft shall not end with a hand in the off-axis too close to the place, to prevent the bearing shell or round when Jishang fingers. Grilled loading operation, the wedge should be stuffed. (5) According to the frequency of use, the proposed 0.5-1a 1 hydraulic oil change, long after the closure, the restoration prior to the use of hydraulic oil and replace the seals. 7 Conclusion mine car wheels changer at Mine Run 1a, the device performance, reliable, removable wheel assembly aircraft, bearing in one, compact structure, easy operation, high efficiency, maintenance of good quality. Large to reduce the labor intensity and improve the working environment, reduce maintenance and use costs, extended wheel life, mine is the ideal wheel for maintenance equipment. References: [1] Zhu true, et al. Patent mine car wheel changer: China, ZL03220198.2. New patent. 2004-02. Author: Lu Yun Po (1969 a), Hebei Laoting who graduated from the Hebei Institute of Architectural Technology in 1996, graduated from coal has been Kailuan Mining Co Ltd Electrical Division Fangezhuang engaged in technical work, published many articles , Tel :0516 -3885357. Received a 157 for a date: 2008.01.18
More articles related to topics：

[link widoczny dla zalogowanych]

ugg boots sale EBJ-120TP boring machine running ge

[link widoczny dla zalogowanych]